Product Description
With the MMOBIEL Dock Connector Alternative Equipment, it is possible for you to to repair your cellphone very quickly! All the pieces you want is inside this DIY Dock Connector Alternative Equipment.
CAUTION: Earlier than dissasembling your cellphone, discharge your battery under 25%! A charged lithium-ion battery can catch hearth or explode if by chance punctured.
BEFORE YOU START: Please create a backup of your iPhone.
Step 1
Energy off your iPhone. Take away the 2 Pentalobe screws, situated on the backside of the iPhone, subsequent to the lightning connector.
Step 2
Use a Warmth Gun or Hair Dryer, to use delicate warmth to the decrease fringe of the iPhone, for approx. one minute.
Step 3
Apply a suction cup to the decrease left nook of the show meeting.Pull up on the suction cup with agency, fixed strain, to create a slight hole between the entrance panel and rear case.Place the flat fringe of a spudger into the hole between the display screen and rear case, straight above the headphone jack, and twist the spudger to widen the hole.Slide the spudger up the aspect of the cellphone to separate the adhesive and free the clips.
Step 4
Use the suction cup to open the show, breaking the final of the adhesive. Open the iPhone like a ebook. The entrance panel continues to be related to the again case on the left aspect of the cellphone.CAUTION: Don’t open the show additional than 90º, as it’s nonetheless related on the high by three cables which will break if stretched too far.
Step 5
Take away Phillips screws securing the Battery Connector Bracket.Take away the Bracket.
Step 6
Use the purpose of a spudger to disconnect the Battery Connector by prying it straight up from the logic board.Disconnect the Entrance Digicam Flex Cable.Disconnect the Digitizer Flex Cable.Disconnect the Show Cable
Step 7
Take away the Phillips screws securing the bracket over the entrance panel sensor meeting connector.Take away the bracket
Step 8
Disconnect the entrance panel sensor meeting connector from its socket on the logic board.Take away the entrance panel.
Step 9
Take away the 2 Phillips screws securing the barometric vent to the rear case and take away the vent.Use the flat finish of a spudger to disconnect the Taptic Engine connector from its socket on the logic board.Take away the three Phillips screws securing the Taptic Engine to the rear case.Take away the Taptic Engine.
Step 10
Take away the Phillips screw securing the Wi-Fi variety antenna to the rear case, and take away the screws securing the Loud Speaker.Use the purpose of a spudger to elevate the 2 antenna cable connectors up off of the sockets on the logic board.Use tweezers to take away the antenna cables from the clip on the speaker.
Step 11
Use the tip of a spudger to slip the speaker meeting in the direction of the logic board and off of the rear case.Take away the speaker.
Step 12
Use the flat finish of a spudger to disconnect the rear-facing digicam connector.Take away the Phillips screws securing the rear digicam bracket to the rear case and take away the bracket.Use the pointed finish of a spudger to pry up and disconnect the antenna bus connector, simply left of the rear digicam module.
Step 13
Take away the 2 tri-point screws securing the higher cable bracket and take away the bracket.Use the flat finish of a spudger to disconnect the higher cable connector.
Step 14
Take away the Phillips screws securing the Wi-Fi antenna and take away the antenna.After eradicating the Wifi Antenna, take away the 2 screws and take away the bracket.
Step 15
Take away the standoff screw from the grounding bracket.Use tweezers to softly bend the logic board grounding bracket out of the best way.
Step 16
Use the purpose of a spudger to disconnect the decrease cable connector.
Step 17
Take away the next screws.Use the purpose of a spudger to maneuver the SIM card eject plunger out of the logic board’s means.
Step 18
Use the flat finish of a spudger to softly elevate the battery connector finish of the logic board up.Carry the battery connector finish of the logic board up, and pull it out of the rear case.
Step 19
Take away the Phillips screw from the lightning connector.Take away the spring contact from the lightning connector.Take away the 2 Phillips screws securing the lightning connector cable in place, and the 2 backside screws from the rear case.Use the pointed finish of a spudger to separate the 2 microphones from the underside of the rear case.Ranging from the center of the cellphone, slide a gap choose beneath the lightning connector to separate it from the rear case.
Step 20
Proceed to slip the choose till the lightning connector meeting is not adhered to the rear case.Take away the Dock Connector.Congratulations! You will have now efficiently eliminated your Dock Connector!To reinstall the iPhone, use the earlier steps on this guide and apply them backwards.
Full set: Set Consists of 3 x Screwdriver 1 x Pentalope 1 x Cross 1 x 0.6. Tri-Level 100% Excellent Match Assured
Straightforward Set up Correct Alternative half used to Exchange the damaged broken half! Excellent match Assured. You don’t want a Technician to do it.
Compatibility: Appropriate solely with iPhone 7 A1660 A1778 A1779 NOT with iPhone 7 Plus Necessary: Please examine the Mannequin Quantity earlier than buying this Merchandise. One can find the Mannequin Quantity on the again of your machine (see product photos on the left)
Top quality product by MMOBIEL: Every half is examined earlier than cargo, Merchandise in Inventory!
